NEWS & VIDEO
Cap Mould Engineering Topics & Project Updates
Read practical cap mould engineering notes on hot runner versus cold runner selection, in-mould closing and injection-machine compatibility. Use these guides to prepare your part drawing, output target and tooling requirements. Explore our flip top cap moulds and water and beverage cap moulds, or request a project review.
ENGINEERING NOTE
Choosing a Runner System for Cap Moulds
A hot runner can reduce or avoid runner scrap, while a cold runner changes the mould layout, part separation and material handling. Compare cavity count, cap weight, resin, injection-machine capacity, maintenance access and total production needs before choosing a system.
TRIAL FOCUS
Automatic Closing Flip-top Mould
The cap must leave the cavity without damaging the living hinge, then move through its closing sequence consistently. During a trial, check hinge stress, lid alignment, snap fit, ejection marks and the condition of parts produced over repeated cycles.
DESIGN CHECK
Mould Design for Limited Machine Tonnage
A cavity target alone cannot establish machine compatibility. Compare the mould envelope with tie-bar spacing, platen and mounting details; review shot capacity, opening stroke, ejection and clamping needs before fixing the cavity and runner arrangement.
Mould trials, products & workshop videos
Selected videos from our project archive. Each clip relates to its own tooling or product example. Select Play to load the YouTube player.
Flip-top mould with in-mould closing
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Flip-top cap mould trial
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Water cap mould trial
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Multi-cavity cap mould
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Sports cap mould trial
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Engine oil cap mould trial
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Oil cap mould trial
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Measuring cup mould
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Syringe mould trial & product inspection
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Handle mould trial
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗PET preform mould
Archive video from Mincong Mould’s YouTube channel.
Watch on YouTube ↗Cosmetic product samples
Cosmetic product sample display from our archive.
Watch on YouTube ↗Tooling workshop archive
Archive workshop footage; published 2021-12-22.
Watch on YouTube ↗Hot runner assembly
Archive footage of hot runner assembly for a measuring cap mould.
Watch on YouTube ↗Latest Engineering Notes
New technical articles and documented video updates appear here when published.
- Why Is There a Gap Under Your Spray Pump Overcap?Diagnose a gap under a spray pump overcap by checking seating height, pump clearance and the bottle shoulder before modifying the mould.
- Why Does a Flip-Top Cap Reopen After In-Mould Closing?Find out whether a flip-top lid failed to latch in the mould, opened during ejection or reopened during take-out. Use a slow-motion trial comparison.
- Meet Mincong Mould at interpack China 2026 | Booth W5S20Visit Mincong Mould at booth W5S20 during interpack China 2026, 16–18 November at Shanghai New International Expo Centre.
- Why Is Your PET Bottle Thinner on One Side After Blowing?When a PET bottle is thicker on one side, trace marked preforms through blowing to see whether the thin side follows the preform or the blow station.
- Clear PET Preform, White Gate: What Should You Check First?Is the PET preform clear except for a white mark at the gate? Use the appearance, cavity pattern and timing to decide what to check first.
- Why Does Your Powder Shaker Cap Stop Dispensing?A powder shaker cap that stops dispensing may have blocked holes, a misaligned insert or caked powder. Use a simple comparison before changing the mould.