PET preform mould price depends on what is being supplied: the approved preform, cavity arrangement, mould components, hot-runner configuration, machine interfaces and agreed trial and support scope. Cavity count is one input. It is not a complete basis for comparing quotations.
There is no useful single price for every PET preform mould. A budget figure becomes meaningful only when its assumptions and exclusions are visible. This guide explains how to compare those assumptions before requesting a project-specific quotation.
First identify whether the quote covers a complete mould
The expression “PET preform tooling” can refer to different delivery scopes. A proposal may concern a complete new mould, selected replacement components or a conversion of existing tooling.
List what the supplier is pricing. If existing equipment or components are to be retained, identify them and confirm that their interfaces have been reviewed. A component package should not be compared directly with a complete mould as though both deliver the same result.
Also distinguish the injection mould from the injection machine, dryer, cooling equipment and take-out system. Any of these may be needed for the production plan without being included in the mould price.
Preform geometry changes more than the material weight
Provide the approved preform drawing and neck specification. Two preforms of similar weight may have different body geometry, neck-forming requirements or release arrangements.
If the design is still being developed, ask the supplier to state which version forms the quotation basis. Record whether later changes are included, subject to review or outside the quoted scope.
This helps avoid comparing a firm proposal for one defined design with a provisional estimate for another. A sample can support the discussion, but it should not conceal unresolved drawing requirements.
Compare cavity arrangement and output assumptions together
More cavities can increase the number of preforms produced per shot, but the complete output estimate also depends on the observed cycle, available operating time and accepted yield.
For a budget comparison, ask each supplier to identify the proposed cavity arrangement and the assumptions behind its production estimate. Check that the actual injection machine and utilities have been considered.
A lower price per cavity is not automatically the lower investment for the project. Installation changes, additional equipment or an unverified production assumption can alter the comparison.
Identify the hot-runner package in writing
“Hot runner included” is too broad for a quotation comparison. Request the manufacturer, proposed configuration, gate and actuation concept where relevant, controller scope and connection requirements.
For a YUDO proposal, compare the identified system and supplied components. If a Husky hot-runner alternative is proposed, request the same level of detail and confirmation of its suitability and availability for the project.
Do not assume a named brand means that the controller, cables, spare heaters, thermocouples or commissioning services are all included. Keep the included list and exclusions beside the quoted price.
Check which mould components and service items are specified
Ask the supplier to identify the material specifications and treatment requirements for the relevant components. “Stainless steel” or “high quality steel” does not define the complete construction.
Then review what happens when a component needs service. Which items are supplied as spares? How are replacements identified? What information is provided for maintenance?
If future weight or neck changes are discussed, separate the current supply from an optional conversion. A statement that some inserts are replaceable is not a quotation for every future product change.
Make the trial scope comparable
A quotation should explain what the trial is expected to demonstrate, using which material and equipment. Identify the sample and measurement scope, any required handling arrangement and the documents supplied.
If final bottle validation is required, state who performs it and what is included. A successful preform injection demonstration is not the same deliverable as a completed bottle-development programme.
Where site commissioning is offered, clarify travel, duration and responsibilities in the commercial proposal. The article provides a comparison method; the agreed quotation and contract determine the actual obligations.
Use a comparison table before negotiating
Complete this table from the suppliers' written offers. Leave an item unresolved if the answer is missing.
| Comparison item | What should match or be explained |
|---|---|
| Product basis | Preform and neck drawing revisions, material and intended application |
| Tooling scope | Complete mould, replacement package or defined conversion |
| Production basis | Cavities, cycle assumptions, machine and utility dependencies |
| Hot runner | Identified configuration, controller and included accessories |
| Verification | Trial conditions, samples, measurements and records |
| After-sales scope | Spares, documents, warranty terms and commissioning |
| Commercial basis | Currency, delivery terms, packing, freight and exclusions |
Do not fill a blank with an assumption that favours the cheaper offer. Ask for clarification, then update the comparison.
Request a quotation that can become an order
Send the current preform drawing, neck details, bottle application, material specification, machine information and production target. Add any existing tooling that is intended to be reused.
If some information is unavailable, identify it clearly. A supplier can distinguish a preliminary budget from a confirmed scope rather than presenting uncertain inputs as a firm engineering conclusion.
Visit our PET preform mould page and the preform versus blow mould explanation if you need to confirm the tooling stage. Request a PET preform mould review from Mincong with the information you already have.